| |
SAE
Grade
|
Markings
|
Tensile
PSI
|
Material
|
5/16 |
3/8 |
7/16 |
1/2 |
9/16 |
5/8 |
3/4 |
7/8 |
Brass
|
|
60,000
|
Copper 63%
Zinc 37%
|
9
|
17
|
27
|
37
|
49
|
78
|
104
|
160
|
Stainless
|
|
72,000
|
AISI 303
|
10
|
18
|
28
|
40
|
54
|
80
|
117
|
180
|
2
|
|
74,000
|
Low
Carbon
|
12
|
20
|
32
|
47
|
69
|
96
|
155
|
206
|
3
|
|
100,000 |
Medium
Carbon
|
17
|
30
|
47
|
69
|
103
|
145
|
234
|
372
|
5
|
|
120,000 |
Medium
Carbon Heat
Treated
|
19
|
33
|
54
|
78
|
114
|
154
|
257
|
382
|
6
|
|
133,000 |
Medium
Carbon
Tempered
|
24
|
43
|
69
|
106
|
150
|
209
|
350
|
550
|
7
|
|
133,000 |
Medium
Carbon
Alloy
|
25
|
44
|
71
|
110
|
154
|
215
|
360
|
570
|
8
|
|
150,000 |
Medium
Carbon
Alloy
|
29
|
47
|
78
|
119
|
169
|
230
|
380
|
600
|
10
|
|
160,000 |
High
Carbon
Case Hardened
|
33
|
54
|
84
|
125
|
180
|
250
|
400
|
640
|
Safety Notes
These values are given in lb-ft and apply to clean
smooth lubricated threads on NEW fasteners.
The nut and washer must have equal or greater rating
then the bolt.
Consult your manual for material type
The values are for the fastener not the assembly.
Some assembles can not with stand the maximum clamping force.
The values for fine treads are slightly higher.
Compiled By Chris Klossner
Home
| Forums
Today's Featured Article -
My Ford Golden Jubilee - by Troy Estes. This article is about my '53 Ford Jubilee and a story that starts with taking the tractor to my brother's Starter/Alternator Rebuilding shop for a wiring fix. The generator was shot as well as all the wiring. I dropped off the tractor expecting a transformation from a 6 volt to a 12 volt system utilizing the original generator housing, and a total rewiring of the whole tractor. The front end center pin bushing was worn also so I ask that they replace it if they had time. Well, that’s wha
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
|
|